SCB10干式变压器（选型表）由台州力威电源科技有限公司提供，SCB10型环氧树脂浇注三相干式变压器具有安全，阻燃防火，无污染，可直接安装在负荷中心。免维护、安装简便。防潮性能好，停运后不经预干燥即可投入运行。损耗低，局部放电量低、噪音小、强迫风冷条件下可以120% 额定负载运行。自己备有完善的温度保护控制系统，为变压器安全运行提供可靠保障。该产品的可靠性指标已经达到国内先进水平。
SCB10 epoxy resin cast three-phase dry-type transformer has safety, fire-retardant and fire-proof, no pollution, and can be directly installed in the load center. Maintenance free and easy to install. It has good moisture-proof performance and can be put into operation without pre-drying after shutdown. Low loss, low partial discharge, low noise, and 120% rated load operation under forced air cooling. It has a complete temperature protection control system to provide reliable protection for the safe operation of the transformer. The reliability index of this product has reached the domestic advanced level.
| 型号含义 Meaning |
| 特点 Characteristics |
1、线圈采用铜导线缠绕或箔绕，以玻璃纤维增强，环氧树脂不加填料真空干燥脱气脱湿整体浇注，机械强度高，抗短路，耐冲击能力强。
2、高压绕组首末端及中间分接抽头采用铜嵌件预埋结构，钢性好，便于调档，美观整齐。
3、铁芯采用优质晶粒取向冷轧硅钢片叠制，45度全斜多阶梯接缝。表面用树脂绝缘涂层覆盖，耐潮湿，防锈，降噪。
4、铁芯、夹件和线圈之间采用弹性件夹紧，使线圈处于稳定压紧状态，以降低噪音。
5、变压器按自冷设计，整体浇注的高(低)压线圈筒壁内部预留有纵向通风道，可配备强迫风冷装置(冷却风机)，采用强迫风冷装置后，可提高输出容量20%。
6、配有温控器，在低压线圈顶部的预埋孔内放置铂电阻(Pt100)。以监测变压器绕组温升，自动启停冷却风机并设有故障报警、超温报警和超温跳闸功能，为干式变压器提供可靠的过载保护装置，从而提高干式变压器运行的安全性。
1. The coil is wound by copper wire or foil, reinforced with glass fiber, epoxy resin without filler vacuum drying, degassing and dehumidification, casting, high mechanical strength, short circuit resistance and strong impact resistance.
2. The first end of the high-voltage winding and the intermediate tapping tap are embedded with copper inserts. The steel is good, easy to shift, beautiful and neat.
3. the iron core is made of high-quality grain oriented cold-rolled silicon steel sheet, 45 degree full oblique multi-step seam. The surface is covered with a resin insulating coating to resist moisture, rust and noise.
4. The elastic core is clamped between the iron core, the clamp and the coil, so that the coil is in a stable compression state to reduce noise.
5. The transformer is designed according to self-cooling. There is a longitudinal air duct inside the high (low) pressure coil wall of the whole casting. It can be equipped with forced air cooling device (cooling fan). After forced air cooling device, the output capacity can be increased. %.
6. With a thermostat, place a platinum resistor (Pt100) in the pre-buried hole at the top of the low voltage coil. In order to monitor the temperature rise of the transformer winding, the cooling fan is automatically started and stopped, and the fault alarm, over-temperature alarm and over-temperature trip function are provided to provide a reliable overload protection device for the dry-type transformer, thereby improving the safety of the dry-type transformer operation.
| 产品结构 Structure |
铁芯：铁芯选用进口优质冷轧硅钢片，三阶全斜接缝结构，芯柱采用F级无纬带绑扎，铁芯表面采用环氧树脂包封，降低了空载损耗，空载电流和铁皮噪声，夹件和紧回件经特殊表面处理，使产品外观质量有了进一步提高。
温控系统和风冷系统：采用横流顶吹式冷却风机，该冷却风机具有噪声小，风压高，外形美观等特点，增强了变压器的过载能力。温度控制采用智能温控仪，提高了变压器运行安全可靠性。
保护外壳和出线母排：保护外壳对变压器作进一步安全保护，防护等级有IP20、IP23等。外壳材料有铝合金、冷轧钢板，不锈钢等供用户选择。低压出线用标准母线排出线，侧出线和顶出线均可，也可为用户设计特殊出线方式。
Iron core: The iron core is made of imported high-quality cold-rolled silicon steel sheet, the third-order full-slant joint structure, the core column is bundled with F-class non-latitude belt, and the iron core surface is sealed with epoxy resin, which reduces the no-load loss and no-load current. And the iron sheet noise, the clip and the back part are specially treated to improve the appearance quality of the product.
Temperature control system and air cooling system: The cross-flow top-blown cooling fan is adopted. The cooling fan has the characteristics of low noise, high wind pressure and beautiful appearance, which enhances the overload capability of the transformer. The temperature control adopts an intelligent temperature controller to improve the safety and reliability of the transformer operation.
Protective casing and outlet busbar: The protective casing provides further protection for the transformer. The protection grades are IP20, IP23 and so on. The outer casing material is aluminum alloy, cold rolled steel plate, stainless steel, etc. for users to choose. The standard busbar discharge line for low-voltage outlets can be used for both side outlets and top outlets. Special outlets can also be designed for users.
| 产品用料 Materials |
| 材料名称 Component | 材质 Material | 产地及质量特点 Place of origin and Characteristics | ||||
| 硅钢片 Silicon steel sheet | 全新优质晶粒取向高导磁冷轧硅钢片 New high quality grain oriented high permeability magnetic cold rolled silicon steel sheet | 产地：武钢或新日铁。激磁电流、铁损耗、饱和参数性能优越。冷轧硅钢带由于具有较高的导磁系数和较低的损耗，因此用来制作变压器具有体积小、重量轻、效率高的优势。热轧硅钢带则逊色于冷轧硅钢带，而二次片、拼接片等对变压器使用寿命危害就更不用说了。 Origin: WISCO or Nippon Steel. Excitation current, iron loss, and saturation parameters are superior. Cold-rolled silicon steel strips have the advantages of small size, light weight and high efficiency due to their high magnetic permeability and low loss. Hot-rolled silicon steel strips are inferior to cold-rolled silicon steel strips, and secondary sheets, splices, etc. are not harmful to the service life of transformers. | ||||
| 变压器绕组 Transformer winding | 紫铜 Copper | 产地：洛阳铜业。含铜量99.999%，国家规定：电工用铜纯度必须在99.5%以上的紫铜。黄铜可用在小功率非电力变压器上，且属于不合格违规使用。另用黄铜做变压器线圈会增加铜损（负载损耗），降低变压器使用功率等，是十分有害的。 Origin: Luoyang Copper. The copper content is 99.999%, and the state stipulates that the copper purity of the electrician must be 99.5% or more. Brass can be used on low-power non-power transformers and is a non-conforming violation. Another use of brass as a transformer coil will increase copper loss (load loss) and reduce the power used by the transformer. It is very harmful. | ||||
| 母排 Busbar | ||||||
| 绝缘油 Insulating oil | 环烷基矿物油 Cycloalkyl mineral oil | 产地：新疆克拉玛依油田。清洁而透明的液体，不得有沉淀物、机械杂质悬浮物及棉絮状物质。劣质油或二次油存在加速变压器老化，噪音大、易短路烧毁，使用寿命短。 Origin: Xinjiang Karamay Oilfield. Clean and transparent liquids must be free of deposits, suspended solids of mechanical impurities and cotton-like materials. Inferior oil or secondary oil exists to accelerate the aging of the transformer, the noise is large, the short circuit is easy to burn, and the service life is short. | ||||
| 绝缘纸 Insulating paper | 牛皮纸/NOMEX 绝缘纸 Kraft paper / NOMEX insulation paper | 产地：许昌绝缘材料厂或美国杜邦公司。绝缘纸是变压器的重要组成部分，变压器老化、烧坏的主要原因之一是使用低价劣质绝缘纸，易发生电弧击穿，缩短了使用寿命。 Origin: Xuchang Insulation Material Factory or DuPont Company of the United States. Insulation paper is an important part of the transformer. One of the main reasons for the aging and burning of the transformer is the use of low-cost inferior insulating paper, which is prone to arc breakdown and shortens the service life. | ||||
| 环氧树脂 Epoxy resin | 高环氧值(>40)6101环氧树脂 igh epoxy value (>40) 6101 epoxy resin | 产地：瑞士汽巴嘉吉。F/H级蕞高耐温155℃/180℃。耐温、耐压、硬度、收缩率、吸水率、玻化温度、粘接强度、拉伸强度等技术指标对干式变压器绝缘、浇注质量非常关键。 Origin: Swiss Ciba Cargill. The F/H grade has a maximum temperature resistance of 155 ° C / 180 ° C. Technical indexes such as temperature resistance, pressure resistance, hardness, shrinkage, water absorption, glass transition temperature, bonding strength and tensile strength are critical to the insulation and casting quality of dry-type transformers. | ||||
| 电工木 Electrician wood | 榉树木 Eucalyptus | 产地：东南亚、内蒙古，由南方机车厂、内蒙古阿里河电厂提供，绝缘能力强，抗张强度高。 Origin: Southeast Asia, Inner Mongolia, provided by Southern Locomotive Works and Inner Mongolia Alihe Power Plant, with strong insulation and high tensile strength. | ||||
| 技术参数 Parameters |
| 变压器型号（选型表） Transformer Type | 电压组合 Voltage Combination | 联结组别 Connection Group | 短路阻抗 Short- circuit Impedance | 损耗(W) Loss | 空载电流 No-load current （%） | |||
| 高压 HV | 分接范围 Tap Range | 低压 LV | 空载 No-load Loss | 负载 Load Loss | ||||
| SCB10-30/10-0.4 | 11 10.5 10 6.3 6 | ±5% 或 ±2×2.5% | 0.4 0.69 | Yyn0 或 Dyn11 | 4% | 190 | 710 | 2.4 |
| SCB10-50/10-0.4 | 270 | 1000 | 2.4 | |||||
| SCB10-63/10-0.4 | 345 | 1220 | 2.1 | |||||
| SCB10-80/10-0.4 | 370 | 1380 | 1.8 | |||||
| SCB10-100/10-0.4 | 400 | 1570 | 1.8 | |||||
| SCB10-125/10-0.4 | 470 | 1850 | 1.6 | |||||
| SCB10-160/10-0.4 | 540 | 2130 | 1.6 | |||||
| SCB10-200/10-0.4 | 620 | 2530 | 1.4 | |||||
| SCB10-250/10-0.4 | 720 | 2760 | 1.4 | |||||
| SCB10-315/10-0.4 | 880 | 3470 | 1.2 | |||||
| SCB10-400/10-0.4 | 980 | 3990 | 1.2 | |||||
| SCB10-500/10-0.4 | 1160 | 4880 | 1.2 | |||||
| SCB10-630/10-0.4 | 6% | 1340 | 5880 | 1.0 | ||||
| SCB10-800/10-0.4 | 1520 | 6960 | 1.0 | |||||
| SCB10-1000/10-0.4 | 1770 | 8130 | 1.0 | |||||
| SCB10-1250/10-0.4 | 2090 | 9690 | 1.0 | |||||
| SCB10-1600/10-0.4 | 2450 | 11730 | 1.0 | |||||
| SCB10-2000/10-0.4 | 3050 | 14450 | 0.8 | |||||
| SCB10-2500/10-0.4 | 3600 | 17170 | 0.8 | |||||
| 注：以上参数仅供参考，具体以实际为准。我公司不断对产品进行优化设计，如有改动，恕不另行通知，解释权归台州力威电源科技有限公司所有！ Note: The above parameters are for reference only, which is subject to actual conditions. Our company continuously optimizes the design of the products, and if there are any changes without prior notice, the right of interpretation belongs to Taizhou Liwei Power Technology Co., Ltd.! | ||||||||
| 执行标准 Standard |
1、GB1094.11-2007 干式电力变压器
2、GB/T10228-2008 干式电力变压器技术参数和要求
3、GB1094.10-2003 电力变压器第3部分：绝缘水平、绝缘试验和外绝缘空气间隙
4、JB/T10008-2004 6~500KV级变压器声级
5、JB/T56009-1998 干式电力变压器产品质量分等
1. GB1094.11-2007 dry power transformer
2. GB/T10228-2008 dry power transformer technical parameters and requirements
3. GB1094.10-2003 Power transformers - Part 3: Insulation level, insulation test and external insulation air gap
4. JB/T10008-2004 6~500KV class transformer sound level
5. JB/T56009-1998 dry power transformer product quality grading
| 安装尺寸 Size |
| 变压器型号 Transformer Type | 外形尺寸(mm) Dimensions | 安装轨距(mm) Installation Gauge | 重量(Kg) Weight | ||||||
| SCB10-30/10-0.4 | 645*460*660 | 400*400 | 265 | ||||||
| SCB10-50/10-0.4 | 690*460*710 | 400*400 | 300 | ||||||
| SCB10-63/10-0.4 | 810*460*790 | 500*400 | 395 | ||||||
| SCB10-80/10-0.4 | 830*460*880 | 500*400 | 485 | ||||||
| SCB10-100/10-0.4 | 910*800*925 | 550*740 | 575 | ||||||
| SCB10-125/10-0.4 | 910*800*955 | 550*740 | 620 | ||||||
| SCB10-160/10-0.4 | 910*800*1000 | 550*740 | 650 | ||||||
| SCB10-200/10-0.4 | 940*900*1090 | 550*820 | 900 | ||||||
| SCB10-250/10-0.4 | 980*900*1160 | 550*820 | 1020 | ||||||
| SCB10-315/10-0.4 | 1020*900*1235 | 550*820 | 1280 | ||||||
| SCB10-400/10-0.4 | 1030*900*1260 | 550*820 | 1450 | ||||||
| SCB10-500/10-0.4 | 1140*890*1315 | 660*820 | 1560 | ||||||
| SCB10-630/10-0.4 | 1210*890*1250 | 660*820 | 1650 | ||||||
| SCB10-800/10-0.4 | 1350*890*1350 | 820*820 | 1970 | ||||||
| SCB10-1000/10-0.4 | 1380*890*1350 | 820*820 | 2170 | ||||||
| SCB10-1250/10-0.4 | 1425*890*1430 | 820*820 | 2750 | ||||||
| SCB10-1600/10-0.4 | 1420*1100*1680 | 820*1020 | 3200 | ||||||
| SCB10-2000/10-0.4 | 1540*1200*1735 | 1070*1120 | 3710 | ||||||
| SCB10-2500/10-0.4 | 1550*1200*1905 | 1070*1120 | 4460 | ||||||
注：以上参数仅供参考，具体以实际为准。我公司不断对产品进行优化设计，如有改动，恕不另行通知，解释权归台州力威电源科技有限公司所有！ Note: The above parameters are for reference only, which is subject to actual conditions. Our company continuously optimizes the design of the products, and if there are any changes without prior notice, the right of interpretation belongs to Taizhou Liwei Power Technology Co., Ltd.! | |||||||||
| 订货须知 order |
1、产品型号
2、额定容量(kVA)，三绕组变压器高、中、低压绕组容量比(％)
3、高压额定电压(kV)，调压方式，级数及分接电压百分比(％)
4、中压额定电压(kV)，调压方式，级数及分接电压百分比(％)
5、低压额定电压(kV)
6、短路阻抗(％)
7、联结组标号
8、冷却方式
9、特殊要求：如环境温度、海拔高度、相数、频率、有载分接开关、绝缘水平、环境要求。
服 务 热 线